Product Description
SPROCKET 1” X 17.02mm 16B SERIES SPROCKETS
| For Chain Acc.to DIN8187 ISO/R 606 | |||||
| Tooth Radius r3 | 26.0mm | ||||
| Radius Width C | 2.5mm | ||||
| Tooth Width b1 | 15.8mm | ||||
| Tooth Width B1 | 16.2mm | ||||
| Tooth Width B2 | 47.7mm | ||||
| Tooth Width B3 | 79.6mm | ||||
| 16B SERIES ROLLER CHAINS | |||||
| Pitch | 25.4 mm | ||||
| Internal Width | 17.02 mm | ||||
| Roller Diameter | 15.88mm | ||||
Products Show
| Z | de | dp | SIMPLEX | DUPLEX | TRIPLEX | ||||||
| dm | D1 | A | dm | D2 | A | dm | D2 | A | |||
| 8 | 77.0 | 66.37 | 42 | 16 | 35 | 42 | 16 | 65 | 42 | 20 | 95 |
| 9 | 85.0 | 74.27 | 50 | 16 | 35 | 50 | 16 | 65 | 50 | 20 | 95 |
| 10 | 93.0 | 82.19 | 55 | 16 | 35 | 56 | 16 | 65 | 56 | 20 | 95 |
| 11 | 105.1 | 90.14 | 61 | 16 | 40 | 64 | 20 | 70 | 64 | 25 | 100 |
| 12 | 109.0 | 98.14 | 69 | 16 | 40 | 72 | 20 | 70 | 72 | 25 | 100 |
| 13 | 117.0 | 106.12 | 78 | 16 | 40 | 80 | 20 | 70 | 80 | 25 | 100 |
| 14 | 125.0 | 114.15 | 84 | 16 | 40 | 88 | 20 | 70 | 88 | 25 | 100 |
| 15 | 133.0 | 122.17 | 92 | 16 | 40 | 96 | 20 | 70 | 96 | 25 | 100 |
| 16 | 141.0 | 130.20 | 100 | 20 | 45 | 104 | 20 | 70 | 104 | 25 | 100 |
| 17 | 149.0 | 138.22 | 100 | 20 | 45 | 112 | 20 | 70 | 112 | 25 | 100 |
| 18 | 157.0 | 146.28 | 100 | 20 | 45 | 120 | 20 | 70 | 120 | 25 | 100 |
| 19 | 165.2 | 154.33 | 100 | 20 | 45 | 128 | 20 | 70 | 128 | 25 | 100 |
| 20 | 173.2 | 162.38 | 100 | 20 | 45 | 130 | 20 | 70 | 130 | 25 | 100 |
| 21 | 181.2 | 170.43 | 110 | 20 | 50 | 130 | 25 | 70 | *130 | 25 | 100 |
| 22 | 189.3 | 178.48 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 23 | 197.5 | 186.53 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 24 | 205.5 | 194.59 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 25 | 213.5 | 202.66 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 26 | 221.6 | 210.72 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 27 | 229.6 | 218.79 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 28 | 237.7 | 226.85 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 29 | 245.8 | 234.92 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 30 | 254.0 | 243.00 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 31 | 262.0 | 251.08 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 32 | 270.0 | 259.13 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 33 | 278.5 | 267.21 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 34 | 287.0 | 275.28 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 35 | 296.2 | 283.36 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 36 | 304.6 | 291.44 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 37 | 312.6 | 299.51 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 38 | 320.7 | 307.59 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 39 | 328.8 | 315.67 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 40 | 336.9 | 323.75 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 41 | 345.0 | 331.81 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 42 | 353.0 | 339.89 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 43 | 361.1 | 347.97 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 44 | 369.1 | 356.05 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 45 | 377.1 | 364.12 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 46 | 385.2 | 372.20 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 47 | 393.2 | 380.28 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 48 | 401.3 | 388.36 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 49 | 409.3 | 396.44 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 50 | 417.4 | 404.52 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 51 | 425.5 | 412.60 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 52 | 433.6 | 420.68 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 53 | 441.7 | 428.76 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 54 | 448.3 | 436.84 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 55 | 457.9 | 444.92 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 56 | 466.0 | 453.01 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 57 | 474.0 | 461.08 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 58 | 482.1 | 469.16 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 59 | 490.2 | 477.24 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 60 | 498.3 | 485.23 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 62 | 514.5 | 501.49 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 64 | 530.7 | 517.65 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 65 | 538.8 | 525.73 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 66 | 546.8 | 533.80 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 68 | 562.9 | 549.98 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 70 | 579.2 | 566.15 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 72 | 595.4 | 582.31 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 75 | 619.7 | 606.56 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 76 | 627.0 | 614.64 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 78 | 643.3 | 630.81 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 80 | 660.0 | 646.97 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 85 | 699.9 | 687.39 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 90 | 740.3 | 727.80 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 95 | 781.1 | 768.22 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 100 | 821.1 | 808.64 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 110 | 902.0 | 889.48 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 114 | 934.3 | 921.81 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 120 | 982.8 | 970.32 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 125 | 1571.3 | 1571.73 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
Notice: *welding hub
BASIC INFO.
| Product name | DIN ISO Standard Sprocket for Roller Chain |
| Materials Available | 1. Stainless Steel: SS304, SS316, etc |
| 2. Alloy Steel: C45, 45Mn, 42CrMo, 20CrMo, etc | |
| 3. OEM according to your request | |
| Surface Treatment | Heat treatment, Quenching treatment, High frequency normalizing treatment, Polishing, Electrophoresis paint processing, Anodic oxidation treatment, etc |
| Characteristic | Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc |
| Design criterion | ISO DIN ANSI & Customer Drawings |
| Size | Customer Drawings & ISO standard |
| Application | Industrial transmission equipment |
| Package | Wooden Case / Container and pallet, or made-to-order |
| Certificate | ISO9001: 2008 |
| Advantage | Quality first, Service first, Competitive price, Fast delivery |
| Delivery Time | 20 days for samples. 45 days for official order. |
INSTALLATION AND USING
The chain wheel, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.
NOTICE
When fitting new chain spoket it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.
It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.
During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
FOR CHAIN STHangZhouRDS
Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.
ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25
| ASME/ANSI B29.1-2011 Roller Chain Standard Sizes | ||||
| Size | Pitch | Maximum Roller Diameter | Minimum Ultimate Tensile Strength | Measuring Load |
|---|---|---|---|---|
| 25 | 0.250 in (6.35 mm) | 0.130 in (3.30 mm) | 780 lb (350 kg) | 18 lb (8.2 kg) |
| 35 | 0.375 in (9.53 mm) | 0.200 in (5.08 mm) | 1,760 lb (800 kg) | 18 lb (8.2 kg) |
| 41 | 0.500 in (12.70 mm) | 0.306 in (7.77 mm) | 1,500 lb (680 kg) | 18 lb (8.2 kg) |
| 40 | 0.500 in (12.70 mm) | 0.312 in (7.92 mm) | 3,125 lb (1,417 kg) | 31 lb (14 kg) |
| 50 | 0.625 in (15.88 mm) | 0.400 in (10.16 mm) | 4,880 lb (2,210 kg) | 49 lb (22 kg) |
| 60 | 0.750 in (19.05 mm) | 0.469 in (11.91 mm) | 7,030 lb (3,190 kg) | 70 lb (32 kg) |
| 80 | 1.000 in (25.40 mm) | 0.625 in (15.88 mm) | 12,500 lb (5,700 kg) | 125 lb (57 kg) |
| 100 | 1.250 in (31.75 mm) | 0.750 in (19.05 mm) | 19,531 lb (8,859 kg) | 195 lb (88 kg) |
| 120 | 1.500 in (38.10 mm) | 0.875 in (22.23 mm) | 28,125 lb (12,757 kg) | 281 lb (127 kg) |
| 140 | 1.750 in (44.45 mm) | 1.000 in (25.40 mm) | 38,280 lb (17,360 kg) | 383 lb (174 kg) |
| 160 | 2.000 in (50.80 mm) | 1.125 in (28.58 mm) | 50,000 lb (23,000 kg) | 500 lb (230 kg) |
| 180 | 2.250 in (57.15 mm) | 1.460 in (37.08 mm) | 63,280 lb (28,700 kg) | 633 lb (287 kg) |
| 200 | 2.500 in (63.50 mm) | 1.562 in (39.67 mm) | 78,175 lb (35,460 kg) | 781 lb (354 kg) |
| 240 | 3.000 in (76.20 mm) | 1.875 in (47.63 mm) | 112,500 lb (51,000 kg) | 1,000 lb (450 kg |
For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):
| Pitch (inches) | Pitch expressed in eighths |
ANSI standard chain number |
Width (inches) |
|---|---|---|---|
| 1⁄4 | 2⁄8 | 25 | 1⁄8 |
| 3⁄8 | 3⁄8 | 35 | 3⁄16 |
| 1⁄2 | 4⁄8 | 41 | 1⁄4 |
| 1⁄2 | 4⁄8 | 40 | 5⁄16 |
| 5⁄8 | 5⁄8 | 50 | 3⁄8 |
| 3⁄4 | 6⁄8 | 60 | 1⁄2 |
| 1 | 8⁄8 | 80 | 5⁄8 |
Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.
Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.
Roller chains made using ISO standard are sometimes called as isochains.
WHY CHOOSE US
1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System
The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.
We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.
Q:Why choose us ?
A. we are a manufacturer, we have manufactured Chain and Sprocket for over 20 years .
B. Reliable Quality Assurance System;
C. Cutting-Edge Computer-Controlled CNC Machines;
D. Bespoke Solutions from Highly Experienced Specialists;
E. Customization and OEM Available for Specific Application;
F. Extensive Inventory of Spare Parts and Accessories;
G. Well-Developed CZPT Marketing Network;
H. Efficient After-Sale Service System
Q. what is your payment term?
A: 30% TT deposit, 70% balance T/T before shipping.
Q:Can we print our logo on your products?
A: yes, we offer OEM/ODM service, we support the customized logo, size, package,etc.
Q: Can you make chains according to my CAD drawings?
A: Yes. Besides the regular standard chains, we produce non-standard and custom-design products to meet the specific technical requirements. In reality, a sizable portion of our production capacity is assigned to make non-standard products.
Q: what is your main market?
A: North America, South America, Eastern Europe, Western Europe, Southeast Asia, Africa, Oceania, Mid East, Eastern Asia,
Q: Can I get samples from your factory?
A: Yes, Samples can be provided.
Q: If products have some quality problem, how would you deal with?
A: We will responsible for all the quality problems.
|
Shipping Cost:
Estimated freight per unit. |
To be negotiated |
|---|
| Standard Or Nonstandard: | Nonstandard |
|---|---|
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car, Motor, Electric Cars, Motorcycle, Machinery |
| Hardness: | Hardened Tooth Surface |
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) | Order Sample |
|---|
| Customization: |
Available
| Customized Request |
|---|
Ensuring Proper Alignment between a Wheel and its Corresponding Sprocket
Proper alignment between a wheel and its corresponding sprocket is crucial for the smooth and efficient operation of the wheel sprocket system. Misalignment can lead to increased wear, noise, and reduced performance. Here are some steps to ensure proper alignment:
- Use Precision Components: Ensure that both the wheel sprocket are high-quality, precision-manufactured components that meet the required specifications. Using well-machined components will aid in achieving better alignment.
- Check Axle Alignment: Make sure the axle or shaft on which the wheel sprocket are mounted is straight and properly aligned. Any misalignment in the axle can lead to misalignment of the wheel sprocket.
- Proper Mounting: Ensure that the wheel sprocket are securely and correctly mounted on the axle or shaft. Use appropriate fasteners and tightening techniques to prevent any movement or shifting during operation.
- Check for Parallelism: The axes of the wheel sprocket should be parallel to each other. Measure the distance between the axes at multiple points to verify parallel alignment.
- Use Alignment Tools: Alignment tools, such as laser alignment systems, can be employed to accurately align the wheel sprocket. These tools can help identify and correct misalignments effectively.
- Check Tension and Tensioner Alignment: If a tensioner is used in the system, ensure that it is properly aligned and applying the right tension to the chain or belt. Incorrect tension can cause misalignment.
- Regular Maintenance: Implement a regular maintenance schedule to check and adjust alignment as needed. Regular inspections can help identify and address alignment issues before they cause significant problems.
- Monitor Performance: Keep an eye on the performance of the wheel sprocket system. Unusual noises, vibrations, or signs of wear can indicate misalignment and should be investigated promptly.
Proper alignment is essential for the long-term performance and reliability of the wheel sprocket system. By following these steps and conducting regular maintenance, you can ensure that the wheel sprocket work together harmoniously, providing efficient power transmission and minimizing wear and tear.
Special Considerations for Using a wheel sprocket System in Off-Road Vehicles
Off-road vehicles operate in rugged and challenging environments, which can put additional stress on the wheel sprocket system. Here are some special considerations to keep in mind when using a wheel sprocket system in off-road vehicles:
- Material Selection: Choose high-quality materials for the wheel sprocket that can withstand rough terrains, impacts, and exposure to elements. Materials like hardened steel or alloys with good impact resistance are commonly used.
- Sealing and Protection: Ensure that the wheel bearings and sprocket teeth are adequately sealed to prevent dirt, mud, water, and other debris from entering. Proper sealing helps to maintain smooth operation and prolong the lifespan of components.
- Reinforcement: Consider reinforcing the wheel sprocket assembly if the vehicle will encounter heavy loads or extreme conditions. Reinforcements can add strength and durability to handle challenging off-road conditions.
- Lubrication: Use a high-quality lubricant suitable for off-road conditions. Frequent lubrication is crucial to reduce friction, prevent corrosion, and protect components from wear and tear.
- Regular Inspection: Off-road vehicles experience higher vibrations and shocks, leading to accelerated wear. Perform regular inspections to detect any signs of damage, misalignment, or wear. Address issues promptly to avoid further problems.
- Shock Absorption: Consider incorporating shock-absorbing features or suspension systems to mitigate the impact on the wheel sprocket system during off-road driving. This helps to protect the components and improve overall vehicle performance.
- Environmental Considerations: Off-road environments often expose the wheel sprocket system to dirt, sand, water, and other harsh elements. Choose coatings or treatments that offer corrosion resistance to protect against environmental damage.
- Weight Consideration: Off-road vehicles may need to be lightweight to navigate difficult terrains effectively. Ensure the wheel sprocket components strike a balance between durability and weight to optimize vehicle performance.
- Service and Maintenance: Establish a regular maintenance schedule and perform necessary servicing after each off-road trip. Cleaning, inspection, and replacement of worn parts are vital to ensure the system’s reliability.
By taking these special considerations into account, the wheel sprocket system in off-road vehicles can withstand the demands of rough terrains and provide reliable performance in challenging environments.
Can a wheel sprocket System be Used in Bicycles and Other Vehicles?
Yes, a wheel sprocket system is commonly used in bicycles and various other vehicles. In bicycles, the wheel sprocket system is a fundamental part of the drivetrain, which transfers power from the rider’s legs to the wheels, propelling the bicycle forward.
The typical bicycle drivetrain consists of a chain, front sprockets (chainrings), rear sprockets (cassette), and the bicycle’s wheels. When the rider pedals the bicycle, the chain engages with the sprockets, and as a result, the rotational motion from the pedaling is transferred to the rear wheel.
The selection of sprocket sizes (number of teeth on chainrings and cassette) can affect the gear ratio, allowing cyclists to adjust their pedaling effort and speed to suit different terrains and riding conditions. Smaller sprockets provide easier pedaling for climbing steep hills, while larger sprockets offer higher speeds on flat or downhill sections.
Beyond bicycles, the wheel sprocket system is widely used in various other vehicles and machinery to transmit power and control speed. It can be found in motorcycles, mopeds, electric scooters, and even some small electric vehicles. Additionally, the wheel sprocket system is prevalent in industrial machinery, where precise speed control and torque transmission are essential.
The efficiency and reliability of the wheel sprocket system make it a versatile and practical choice for many vehicles and mechanical applications.
editor by CX 2023-09-04
China Custom Short Pitch Precision Roller Chains and Bush Chains Customized Chain Sprocket 80b (16B) for Agricultural Machinery by China Manufacturer
Product Description
SPROCKET 1” X 17.02mm 16B SERIES SPROCKETS
| For Chain Acc.to DIN8187 ISO/R 606 | |||||
| Tooth Radius r3 | 26.0mm | ||||
| Radius Width C | 2.5mm | ||||
| Tooth Width b1 | 15.8mm | ||||
| Tooth Width B1 | 16.2mm | ||||
| Tooth Width B2 | 47.7mm | ||||
| Tooth Width B3 | 79.6mm | ||||
| 16B SERIES ROLLER CHAINS | |||||
| Pitch | 25.4 mm | ||||
| Internal Width | 17.02 mm | ||||
| Roller Diameter | 15.88mm | ||||
Products Show
| Z | de | dp | SIMPLEX | DUPLEX | TRIPLEX | ||||||
| dm | D1 | A | dm | D2 | A | dm | D2 | A | |||
| 8 | 77.0 | 66.37 | 42 | 16 | 35 | 42 | 16 | 65 | 42 | 20 | 95 |
| 9 | 85.0 | 74.27 | 50 | 16 | 35 | 50 | 16 | 65 | 50 | 20 | 95 |
| 10 | 93.0 | 82.19 | 55 | 16 | 35 | 56 | 16 | 65 | 56 | 20 | 95 |
| 11 | 105.1 | 90.14 | 61 | 16 | 40 | 64 | 20 | 70 | 64 | 25 | 100 |
| 12 | 109.0 | 98.14 | 69 | 16 | 40 | 72 | 20 | 70 | 72 | 25 | 100 |
| 13 | 117.0 | 106.12 | 78 | 16 | 40 | 80 | 20 | 70 | 80 | 25 | 100 |
| 14 | 125.0 | 114.15 | 84 | 16 | 40 | 88 | 20 | 70 | 88 | 25 | 100 |
| 15 | 133.0 | 122.17 | 92 | 16 | 40 | 96 | 20 | 70 | 96 | 25 | 100 |
| 16 | 141.0 | 130.20 | 100 | 20 | 45 | 104 | 20 | 70 | 104 | 25 | 100 |
| 17 | 149.0 | 138.22 | 100 | 20 | 45 | 112 | 20 | 70 | 112 | 25 | 100 |
| 18 | 157.0 | 146.28 | 100 | 20 | 45 | 120 | 20 | 70 | 120 | 25 | 100 |
| 19 | 165.2 | 154.33 | 100 | 20 | 45 | 128 | 20 | 70 | 128 | 25 | 100 |
| 20 | 173.2 | 162.38 | 100 | 20 | 45 | 130 | 20 | 70 | 130 | 25 | 100 |
| 21 | 181.2 | 170.43 | 110 | 20 | 50 | 130 | 25 | 70 | *130 | 25 | 100 |
| 22 | 189.3 | 178.48 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 23 | 197.5 | 186.53 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 24 | 205.5 | 194.59 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 25 | 213.5 | 202.66 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 26 | 221.6 | 210.72 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 27 | 229.6 | 218.79 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 28 | 237.7 | 226.85 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 29 | 245.8 | 234.92 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 30 | 254.0 | 243.00 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 31 | 262.0 | 251.08 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 32 | 270.0 | 259.13 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 33 | 278.5 | 267.21 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 34 | 287.0 | 275.28 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 35 | 296.2 | 283.36 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 36 | 304.6 | 291.44 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 37 | 312.6 | 299.51 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 38 | 320.7 | 307.59 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 39 | 328.8 | 315.67 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 40 | 336.9 | 323.75 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 41 | 345.0 | 331.81 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 42 | 353.0 | 339.89 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 43 | 361.1 | 347.97 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 44 | 369.1 | 356.05 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 45 | 377.1 | 364.12 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 46 | 385.2 | 372.20 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 47 | 393.2 | 380.28 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 48 | 401.3 | 388.36 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 49 | 409.3 | 396.44 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 50 | 417.4 | 404.52 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 51 | 425.5 | 412.60 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 52 | 433.6 | 420.68 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 53 | 441.7 | 428.76 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 54 | 448.3 | 436.84 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 55 | 457.9 | 444.92 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 56 | 466.0 | 453.01 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 57 | 474.0 | 461.08 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 58 | 482.1 | 469.16 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 59 | 490.2 | 477.24 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 60 | 498.3 | 485.23 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 62 | 514.5 | 501.49 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 64 | 530.7 | 517.65 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 65 | 538.8 | 525.73 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 66 | 546.8 | 533.80 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 68 | 562.9 | 549.98 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 70 | 579.2 | 566.15 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 72 | 595.4 | 582.31 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 75 | 619.7 | 606.56 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 76 | 627.0 | 614.64 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 78 | 643.3 | 630.81 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 80 | 660.0 | 646.97 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 85 | 699.9 | 687.39 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 90 | 740.3 | 727.80 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 95 | 781.1 | 768.22 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 100 | 821.1 | 808.64 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 110 | 902.0 | 889.48 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 114 | 934.3 | 921.81 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 120 | 982.8 | 970.32 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 125 | 1571.3 | 1571.73 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
Notice: *welding hub
BASIC INFO.
| Product name | DIN ISO Standard Sprocket for Roller Chain |
| Materials Available | 1. Stainless Steel: SS304, SS316, etc |
| 2. Alloy Steel: C45, 45Mn, 42CrMo, 20CrMo, etc | |
| 3. OEM according to your request | |
| Surface Treatment | Heat treatment, Quenching treatment, High frequency normalizing treatment, Polishing, Electrophoresis paint processing, Anodic oxidation treatment, etc |
| Characteristic | Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc |
| Design criterion | ISO DIN ANSI & Customer Drawings |
| Size | Customer Drawings & ISO standard |
| Application | Industrial transmission equipment |
| Package | Wooden Case / Container and pallet, or made-to-order |
| Certificate | ISO9001: 2008 |
| Advantage | Quality first, Service first, Competitive price, Fast delivery |
| Delivery Time | 20 days for samples. 45 days for official order. |
INSTALLATION AND USING
The chain wheel, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.
NOTICE
When fitting new chain spoket it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.
It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.
During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
FOR CHAIN STHangZhouRDS
Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.
ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25
| ASME/ANSI B29.1-2011 Roller Chain Standard Sizes | ||||
| Size | Pitch | Maximum Roller Diameter | Minimum Ultimate Tensile Strength | Measuring Load |
|---|---|---|---|---|
| 25 | 0.250 in (6.35 mm) | 0.130 in (3.30 mm) | 780 lb (350 kg) | 18 lb (8.2 kg) |
| 35 | 0.375 in (9.53 mm) | 0.200 in (5.08 mm) | 1,760 lb (800 kg) | 18 lb (8.2 kg) |
| 41 | 0.500 in (12.70 mm) | 0.306 in (7.77 mm) | 1,500 lb (680 kg) | 18 lb (8.2 kg) |
| 40 | 0.500 in (12.70 mm) | 0.312 in (7.92 mm) | 3,125 lb (1,417 kg) | 31 lb (14 kg) |
| 50 | 0.625 in (15.88 mm) | 0.400 in (10.16 mm) | 4,880 lb (2,210 kg) | 49 lb (22 kg) |
| 60 | 0.750 in (19.05 mm) | 0.469 in (11.91 mm) | 7,030 lb (3,190 kg) | 70 lb (32 kg) |
| 80 | 1.000 in (25.40 mm) | 0.625 in (15.88 mm) | 12,500 lb (5,700 kg) | 125 lb (57 kg) |
| 100 | 1.250 in (31.75 mm) | 0.750 in (19.05 mm) | 19,531 lb (8,859 kg) | 195 lb (88 kg) |
| 120 | 1.500 in (38.10 mm) | 0.875 in (22.23 mm) | 28,125 lb (12,757 kg) | 281 lb (127 kg) |
| 140 | 1.750 in (44.45 mm) | 1.000 in (25.40 mm) | 38,280 lb (17,360 kg) | 383 lb (174 kg) |
| 160 | 2.000 in (50.80 mm) | 1.125 in (28.58 mm) | 50,000 lb (23,000 kg) | 500 lb (230 kg) |
| 180 | 2.250 in (57.15 mm) | 1.460 in (37.08 mm) | 63,280 lb (28,700 kg) | 633 lb (287 kg) |
| 200 | 2.500 in (63.50 mm) | 1.562 in (39.67 mm) | 78,175 lb (35,460 kg) | 781 lb (354 kg) |
| 240 | 3.000 in (76.20 mm) | 1.875 in (47.63 mm) | 112,500 lb (51,000 kg) | 1,000 lb (450 kg |
For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):
| Pitch (inches) | Pitch expressed in eighths |
ANSI standard chain number |
Width (inches) |
|---|---|---|---|
| 1⁄4 | 2⁄8 | 25 | 1⁄8 |
| 3⁄8 | 3⁄8 | 35 | 3⁄16 |
| 1⁄2 | 4⁄8 | 41 | 1⁄4 |
| 1⁄2 | 4⁄8 | 40 | 5⁄16 |
| 5⁄8 | 5⁄8 | 50 | 3⁄8 |
| 3⁄4 | 6⁄8 | 60 | 1⁄2 |
| 1 | 8⁄8 | 80 | 5⁄8 |
Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.
Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.
Roller chains made using ISO standard are sometimes called as isochains.
WHY CHOOSE US
1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System
The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.
We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.
Q:Why choose us ?
A. we are a manufacturer, we have manufactured Chain and Sprocket for over 20 years .
B. Reliable Quality Assurance System;
C. Cutting-Edge Computer-Controlled CNC Machines;
D. Bespoke Solutions from Highly Experienced Specialists;
E. Customization and OEM Available for Specific Application;
F. Extensive Inventory of Spare Parts and Accessories;
G. Well-Developed CZPT Marketing Network;
H. Efficient After-Sale Service System
Q. what is your payment term?
A: 30% TT deposit, 70% balance T/T before shipping.
Q:Can we print our logo on your products?
A: yes, we offer OEM/ODM service, we support the customized logo, size, package,etc.
Q: Can you make chains according to my CAD drawings?
A: Yes. Besides the regular standard chains, we produce non-standard and custom-design products to meet the specific technical requirements. In reality, a sizable portion of our production capacity is assigned to make non-standard products.
Q: what is your main market?
A: North America, South America, Eastern Europe, Western Europe, Southeast Asia, Africa, Oceania, Mid East, Eastern Asia,
Q: Can I get samples from your factory?
A: Yes, Samples can be provided.
Q: If products have some quality problem, how would you deal with?
A: We will responsible for all the quality problems.
|
Shipping Cost:
Estimated freight per unit. |
To be negotiated |
|---|
| Standard Or Nonstandard: | Nonstandard |
|---|---|
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car, Motor, Electric Cars, Motorcycle, Machinery |
| Hardness: | Hardened Tooth Surface |
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) | Order Sample |
|---|
| Customization: |
Available
| Customized Request |
|---|
Calculating Torque Requirements for a wheel sprocket Assembly
Calculating the torque requirements for a wheel sprocket assembly involves considering various factors that contribute to the torque load. The torque requirement is crucial for selecting the appropriate motor or power source to drive the system effectively. Here’s a step-by-step guide:
- 1. Determine the Load Torque: Identify the torque required to overcome the resistance or load in the system. This includes the torque needed to move the load, overcome friction, and accelerate the load if applicable.
- 2. Identify the Sprocket Radius: Measure the radius of the sprocket (distance from the center of the sprocket to the point of contact with the chain or belt).
- 3. Calculate the Tension in the Chain or Belt: If using a chain or belt drive, calculate the tension in the chain or belt. Tension affects the torque required for power transmission.
- 4. Account for Efficiency Losses: Consider the efficiency of the system. Not all the input power will be converted into output power due to friction and other losses. Account for this efficiency in your calculations.
- 5. Use the Torque Equation: The torque (T) can be calculated using the following equation:
T = (Load Torque × Sprocket Radius) ÷ (Efficiency × Tension)
It’s essential to use consistent units of measurement (e.g., Newton meters or foot-pounds) for all values in the equation.
Remember that real-world conditions may vary, and it’s advisable to add a safety factor to your calculated torque requirements to ensure the system can handle unexpected peak loads or variations in operating conditions.
Noise and Vibration in wheel sprocket Configurations
In a wheel sprocket configuration, noise and vibration levels can vary depending on several factors:
- Quality of Components: The quality of the wheel sprocket components can significantly impact noise and vibration. Well-manufactured and precisely engineered components tend to produce less noise and vibration.
- Lubrication: Proper lubrication of the sprocket teeth and chain or belt can reduce friction, which in turn helps minimize noise and vibration.
- Alignment: Correct alignment between the wheel sprocket is crucial. Misalignment can lead to increased noise and vibration as the components may not mesh smoothly.
- Tension: Maintaining the appropriate tension in the chain or belt is essential. Insufficient tension can cause the chain to slap against the sprocket teeth, resulting in noise and vibration.
- Speed and Load: Higher speeds and heavier loads can lead to increased noise and vibration levels in the system.
- Wear and Damage: Worn-out or damaged components can create irregularities in motion, leading to increased noise and vibration.
To reduce noise and vibration in a wheel sprocket setup:
- Use high-quality components from reputable suppliers.
- Ensure proper lubrication with appropriate lubricants.
- Regularly inspect and maintain the system to detect any misalignment, wear, or damage.
- Follow manufacturer guidelines for chain or belt tensioning.
- Consider using vibration-damping materials or mounting methods if necessary.
Minimizing noise and vibration not only improves the comfort and safety of the machinery but also extends the life of the components by reducing wear and fatigue.
Role of a wheel sprocket in a Mechanical System
In a mechanical system, a wheel sprocket play a crucial role in transferring motion and power from one component to another. They are essential elements of various machines and mechanisms, such as bicycles, conveyor systems, automobiles, and industrial machinery. Let’s explore their functions in more detail:
1. Wheel:
The wheel is a circular component with a central shaft (axle) that allows it to rotate freely around the axle’s axis. Its primary functions include:
- Motion Transmission: When a force is applied to the wheel’s outer edge, it rotates around the axle, enabling the transfer of linear motion into rotational motion.
- Load Bearing: The wheel’s structure and material are designed to support and distribute the load placed on it, allowing smooth movement over various surfaces.
- Reduction of Friction: By using wheels, the friction between the moving object and the ground is significantly reduced, making it easier to move heavy loads with less effort.
- Directional Control: Wheels can be attached to steering mechanisms to control the direction of movement in vehicles and other equipment.
2. Sprocket:
A sprocket is a toothed wheel designed to mesh with a chain or a belt, facilitating motion transfer between the sprocket and the chain/belt. Its key functions include:
- Power Transmission: When rotational force (torque) is applied to the sprocket, the teeth engage with the links of the chain or belt, transferring motion and power from one sprocket to another.
- Speed and Torque Conversion: Different-sized sprockets can be used to adjust the speed and torque of the driven component in a mechanical system.
- Positive Drive: The teeth on the sprocket and the links on the chain/belt create a positive drive system, reducing the likelihood of slippage or loss of power during operation.
- Chain/Belt Tensioning: Sprockets help maintain proper tension in the chain or belt, ensuring optimal performance and longevity of the power transmission system.
Together, wheels and sprockets form a vital part of mechanical systems, enabling efficient motion transmission, power transfer, and control in a wide range of applications across various industries.
editor by CX 2023-08-02
China wholesaler Short Pitch Precision Roller Chains and Bush Chains Customized Chain Sprocket 80b (16B) for Agricultural Machinery by China Manufacturer with Best Sales
Product Description
SPROCKET 1” X 17.02mm 16B SERIES SPROCKETS
| For Chain Acc.to DIN8187 ISO/R 606 | |||||
| Tooth Radius r3 | 26.0mm | ||||
| Radius Width C | 2.5mm | ||||
| Tooth Width b1 | 15.8mm | ||||
| Tooth Width B1 | 16.2mm | ||||
| Tooth Width B2 | 47.7mm | ||||
| Tooth Width B3 | 79.6mm | ||||
| 16B SERIES ROLLER CHAINS | |||||
| Pitch | 25.4 mm | ||||
| Internal Width | 17.02 mm | ||||
| Roller Diameter | 15.88mm | ||||
Products Show
| Z | de | dp | SIMPLEX | DUPLEX | TRIPLEX | ||||||
| dm | D1 | A | dm | D2 | A | dm | D2 | A | |||
| 8 | 77.0 | 66.37 | 42 | 16 | 35 | 42 | 16 | 65 | 42 | 20 | 95 |
| 9 | 85.0 | 74.27 | 50 | 16 | 35 | 50 | 16 | 65 | 50 | 20 | 95 |
| 10 | 93.0 | 82.19 | 55 | 16 | 35 | 56 | 16 | 65 | 56 | 20 | 95 |
| 11 | 105.1 | 90.14 | 61 | 16 | 40 | 64 | 20 | 70 | 64 | 25 | 100 |
| 12 | 109.0 | 98.14 | 69 | 16 | 40 | 72 | 20 | 70 | 72 | 25 | 100 |
| 13 | 117.0 | 106.12 | 78 | 16 | 40 | 80 | 20 | 70 | 80 | 25 | 100 |
| 14 | 125.0 | 114.15 | 84 | 16 | 40 | 88 | 20 | 70 | 88 | 25 | 100 |
| 15 | 133.0 | 122.17 | 92 | 16 | 40 | 96 | 20 | 70 | 96 | 25 | 100 |
| 16 | 141.0 | 130.20 | 100 | 20 | 45 | 104 | 20 | 70 | 104 | 25 | 100 |
| 17 | 149.0 | 138.22 | 100 | 20 | 45 | 112 | 20 | 70 | 112 | 25 | 100 |
| 18 | 157.0 | 146.28 | 100 | 20 | 45 | 120 | 20 | 70 | 120 | 25 | 100 |
| 19 | 165.2 | 154.33 | 100 | 20 | 45 | 128 | 20 | 70 | 128 | 25 | 100 |
| 20 | 173.2 | 162.38 | 100 | 20 | 45 | 130 | 20 | 70 | 130 | 25 | 100 |
| 21 | 181.2 | 170.43 | 110 | 20 | 50 | 130 | 25 | 70 | *130 | 25 | 100 |
| 22 | 189.3 | 178.48 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 23 | 197.5 | 186.53 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 24 | 205.5 | 194.59 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 25 | 213.5 | 202.66 | 110 | 20 | 50 | *130 | 25 | 70 | *130 | 25 | 100 |
| 26 | 221.6 | 210.72 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 27 | 229.6 | 218.79 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 28 | 237.7 | 226.85 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 29 | 245.8 | 234.92 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 30 | 254.0 | 243.00 | 120 | 20 | 50 | *130 | 25 | 70 | *130 | 30 | 100 |
| 31 | 262.0 | 251.08 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 32 | 270.0 | 259.13 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 33 | 278.5 | 267.21 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 34 | 287.0 | 275.28 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 35 | 296.2 | 283.36 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 36 | 304.6 | 291.44 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 37 | 312.6 | 299.51 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 38 | 320.7 | 307.59 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 39 | 328.8 | 315.67 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 40 | 336.9 | 323.75 | *120 | 25 | 50 | *140 | 25 | 70 | *140 | 30 | 100 |
| 41 | 345.0 | 331.81 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 42 | 353.0 | 339.89 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 43 | 361.1 | 347.97 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 44 | 369.1 | 356.05 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 45 | 377.1 | 364.12 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 46 | 385.2 | 372.20 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 47 | 393.2 | 380.28 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 48 | 401.3 | 388.36 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 49 | 409.3 | 396.44 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 50 | 417.4 | 404.52 | *125 | 25 | 68 | *140 | 25 | 70 | *160 | 30 | 100 |
| 51 | 425.5 | 412.60 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 52 | 433.6 | 420.68 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 53 | 441.7 | 428.76 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 54 | 448.3 | 436.84 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 55 | 457.9 | 444.92 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 56 | 466.0 | 453.01 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 57 | 474.0 | 461.08 | *125 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 58 | 482.1 | 469.16 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 59 | 490.2 | 477.24 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 60 | 498.3 | 485.23 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 62 | 514.5 | 501.49 | *133 | 25 | 68 | *150 | 25 | 85 | *180 | 30 | 110 |
| 64 | 530.7 | 517.65 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 65 | 538.8 | 525.73 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 66 | 546.8 | 533.80 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 68 | 562.9 | 549.98 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 70 | 579.2 | 566.15 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 72 | 595.4 | 582.31 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 75 | 619.7 | 606.56 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 76 | 627.0 | 614.64 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 78 | 643.3 | 630.81 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 80 | 660.0 | 646.97 | *140 | 25 | 68 | *160 | 25 | 90 | *180 | 30 | 110 |
| 85 | 699.9 | 687.39 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 90 | 740.3 | 727.80 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 95 | 781.1 | 768.22 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 100 | 821.1 | 808.64 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 110 | 902.0 | 889.48 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 114 | 934.3 | 921.81 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 120 | 982.8 | 970.32 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
| 125 | 1571.3 | 1571.73 | *140 | 25 | 78 | *160 | 25 | 90 | *180 | 30 | 110 |
Notice: *welding hub
BASIC INFO.
| Product name | DIN ISO Standard Sprocket for Roller Chain |
| Materials Available | 1. Stainless Steel: SS304, SS316, etc |
| 2. Alloy Steel: C45, 45Mn, 42CrMo, 20CrMo, etc | |
| 3. OEM according to your request | |
| Surface Treatment | Heat treatment, Quenching treatment, High frequency normalizing treatment, Polishing, Electrophoresis paint processing, Anodic oxidation treatment, etc |
| Characteristic | Fire Resistant, Oil Resistant, Heat Resistant, CZPT resistance, Oxidative resistance, Corrosion resistance, etc |
| Design criterion | ISO DIN ANSI & Customer Drawings |
| Size | Customer Drawings & ISO standard |
| Application | Industrial transmission equipment |
| Package | Wooden Case / Container and pallet, or made-to-order |
| Certificate | ISO9001: 2008 |
| Advantage | Quality first, Service first, Competitive price, Fast delivery |
| Delivery Time | 20 days for samples. 45 days for official order. |
INSTALLATION AND USING
The chain wheel, as a drive or deflection for chains, has pockets to hold the chain links with a D-profile cross section with flat side surfaces parallel to the centre plane of the chain links, and outer surfaces at right angles to the chain link centre plane. The chain links are pressed firmly against the outer surfaces and each of the side surfaces by the angled laying surfaces at the base of the pockets, and also the support surfaces of the wheel body together with the end sides of the webs formed by the leading and trailing walls of the pocket.
NOTICE
When fitting new chain spoket it is very important that a new chain is fitted at the same time, and vice versa. Using an old chain with new sprockets, or a new chain with old sprockets will cause rapid wear.
It is important if you are installing the chainwheels yourself to have the factory service manual specific to your model. Our chainwheels are made to be a direct replacement for your OEM chainwheels and as such, the installation should be performed according to your models service manual.
During use a chain will stretch (i.e. the pins will wear causing extension of the chain). Using a chain which has been stretched more than the above maximum allowance causes the chain to ride up the teeth of the sprocket. This causes damage to the tips of the chainwheels teeth, as the force transmitted by the chain is transmitted entirely through the top of the tooth, rather than the whole tooth. This results in severe wearing of the chainwheel.
FOR CHAIN STHangZhouRDS
Standards organizations (such as ANSI and ISO) maintain standards for design, dimensions, and interchangeability of transmission chains. For example, the following Table shows data from ANSI standard B29.1-2011 (Precision Power Transmission Roller Chains, Attachments, and Sprockets) developed by the American Society of Mechanical Engineers (ASME). See the references[8][9][10] for additional information.
ASME/ANSI B29.1-2011 Roller Chain Standard SizesSizePitchMaximum Roller DiameterMinimum Ultimate Tensile StrengthMeasuring Load25
| ASME/ANSI B29.1-2011 Roller Chain Standard Sizes | ||||
| Size | Pitch | Maximum Roller Diameter | Minimum Ultimate Tensile Strength | Measuring Load |
|---|---|---|---|---|
| 25 | 0.250 in (6.35 mm) | 0.130 in (3.30 mm) | 780 lb (350 kg) | 18 lb (8.2 kg) |
| 35 | 0.375 in (9.53 mm) | 0.200 in (5.08 mm) | 1,760 lb (800 kg) | 18 lb (8.2 kg) |
| 41 | 0.500 in (12.70 mm) | 0.306 in (7.77 mm) | 1,500 lb (680 kg) | 18 lb (8.2 kg) |
| 40 | 0.500 in (12.70 mm) | 0.312 in (7.92 mm) | 3,125 lb (1,417 kg) | 31 lb (14 kg) |
| 50 | 0.625 in (15.88 mm) | 0.400 in (10.16 mm) | 4,880 lb (2,210 kg) | 49 lb (22 kg) |
| 60 | 0.750 in (19.05 mm) | 0.469 in (11.91 mm) | 7,030 lb (3,190 kg) | 70 lb (32 kg) |
| 80 | 1.000 in (25.40 mm) | 0.625 in (15.88 mm) | 12,500 lb (5,700 kg) | 125 lb (57 kg) |
| 100 | 1.250 in (31.75 mm) | 0.750 in (19.05 mm) | 19,531 lb (8,859 kg) | 195 lb (88 kg) |
| 120 | 1.500 in (38.10 mm) | 0.875 in (22.23 mm) | 28,125 lb (12,757 kg) | 281 lb (127 kg) |
| 140 | 1.750 in (44.45 mm) | 1.000 in (25.40 mm) | 38,280 lb (17,360 kg) | 383 lb (174 kg) |
| 160 | 2.000 in (50.80 mm) | 1.125 in (28.58 mm) | 50,000 lb (23,000 kg) | 500 lb (230 kg) |
| 180 | 2.250 in (57.15 mm) | 1.460 in (37.08 mm) | 63,280 lb (28,700 kg) | 633 lb (287 kg) |
| 200 | 2.500 in (63.50 mm) | 1.562 in (39.67 mm) | 78,175 lb (35,460 kg) | 781 lb (354 kg) |
| 240 | 3.000 in (76.20 mm) | 1.875 in (47.63 mm) | 112,500 lb (51,000 kg) | 1,000 lb (450 kg |
For mnemonic purposes, below is another presentation of key dimensions from the same standard, expressed in fractions of an inch (which was part of the thinking behind the choice of preferred numbers in the ANSI standard):
| Pitch (inches) | Pitch expressed in eighths |
ANSI standard chain number |
Width (inches) |
|---|---|---|---|
| 1⁄4 | 2⁄8 | 25 | 1⁄8 |
| 3⁄8 | 3⁄8 | 35 | 3⁄16 |
| 1⁄2 | 4⁄8 | 41 | 1⁄4 |
| 1⁄2 | 4⁄8 | 40 | 5⁄16 |
| 5⁄8 | 5⁄8 | 50 | 3⁄8 |
| 3⁄4 | 6⁄8 | 60 | 1⁄2 |
| 1 | 8⁄8 | 80 | 5⁄8 |
Notes:
1. The pitch is the distance between roller centers. The width is the distance between the link plates (i.e. slightly more than the roller width to allow for clearance).
2. The right-hand digit of the standard denotes 0 = normal chain, 1 = lightweight chain, 5 = rollerless bushing chain.
3. The left-hand digit denotes the number of eighths of an inch that make up the pitch.
4. An “H” following the standard number denotes heavyweight chain. A hyphenated number following the standard number denotes double-strand (2), triple-strand (3), and so on. Thus 60H-3 denotes number 60 heavyweight triple-strand chain.
A typical bicycle chain (for derailleur gears) uses narrow 1⁄2-inch-pitch chain. The width of the chain is variable, and does not affect the load capacity. The more sprockets at the rear wheel (historically 3-6, nowadays 7-12 sprockets), the narrower the chain. Chains are sold according to the number of speeds they are designed to work with, for example, “10 speed chain”. Hub gear or single speed bicycles use 1/2″ x 1/8″ chains, where 1/8″ refers to the maximum thickness of a sprocket that can be used with the chain.
Typically chains with parallel shaped links have an even number of links, with each narrow link followed by a broad one. Chains built up with a uniform type of link, narrow at 1 and broad at the other end, can be made with an odd number of links, which can be an advantage to adapt to a special chainwheel-distance; on the other side such a chain tends to be not so strong.
Roller chains made using ISO standard are sometimes called as isochains.
WHY CHOOSE US
1. Reliable Quality Assurance System
2. Cutting-Edge Computer-Controlled CNC Machines
3. Bespoke Solutions from Highly Experienced Specialists
4. Customization and OEM Available for Specific Application
5. Extensive Inventory of Spare Parts and Accessories
6. Well-Developed CZPT Marketing Network
7. Efficient After-Sale Service System
The 219 sets of advanced automatic production equipment provide guarantees for high product quality. The 167 engineers and technicians with senior professional titles can design and develop products to meet the exact demands of customers, and OEM customizations are also available with us. Our sound global service network can provide customers with timely after-sales technical services.
We are not just a manufacturer and supplier, but also an industry consultant. We work pro-actively with you to offer expert advice and product recommendations in order to end up with a most cost effective product available for your specific application. The clients we serve CZPT range from end users to distributors and OEMs. Our OEM replacements can be substituted wherever necessary and suitable for both repair and new assemblies.
Q:Why choose us ?
A. we are a manufacturer, we have manufactured Chain and Sprocket for over 20 years .
B. Reliable Quality Assurance System;
C. Cutting-Edge Computer-Controlled CNC Machines;
D. Bespoke Solutions from Highly Experienced Specialists;
E. Customization and OEM Available for Specific Application;
F. Extensive Inventory of Spare Parts and Accessories;
G. Well-Developed CZPT Marketing Network;
H. Efficient After-Sale Service System
Q. what is your payment term?
A: 30% TT deposit, 70% balance T/T before shipping.
Q:Can we print our logo on your products?
A: yes, we offer OEM/ODM service, we support the customized logo, size, package,etc.
Q: Can you make chains according to my CAD drawings?
A: Yes. Besides the regular standard chains, we produce non-standard and custom-design products to meet the specific technical requirements. In reality, a sizable portion of our production capacity is assigned to make non-standard products.
Q: what is your main market?
A: North America, South America, Eastern Europe, Western Europe, Southeast Asia, Africa, Oceania, Mid East, Eastern Asia,
Q: Can I get samples from your factory?
A: Yes, Samples can be provided.
Q: If products have some quality problem, how would you deal with?
A: We will responsible for all the quality problems.
|
Shipping Cost:
Estimated freight per unit. |
To be negotiated|
|
|---|
| Standard Or Nonstandard: | Nonstandard |
|---|---|
| Application: | Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car, Motor, Electric Cars, Motorcycle, Machinery, Marine, Toy, Agricultural Machinery, Car |
| Hardness: | Hardened Tooth Surface |
| Samples: |
US$ 0/Piece
1 Piece(Min.Order) | Order Sample |
|---|
| Customization: |
Available
| Customized Request |
|---|
Choosing the Right Chain Sprocket For Your Bike
When deciding which chain sprocket to buy, you should be aware of how they fit on the bike. These sprockets are often secured to the bike’s shaft by either one or more set screws. ANSI standards for sprocket keyways provide the proper dimensions for a given shaft diameter. However, they aren’t universal and might not apply to all applications. As a result, it is important to consult a supplier who is familiar with the exact keyway dimensions.
Roller chain sprocket
A Roller chain sprocket is a gear with toothed rollers. The tooth profile determines the arc length of the roller. A roller with an undercut tooth profile will not transmit movement properly. For this reason, the pitch line of the roller should be equal to the incremental circle length (r) divided by the number of teeth.
The chain sprocket is available in various types. They can be used in conveyor chains. They are usually available as ready-to-mount units. Finished bores and wide hubs are available for mounting them. They are also available with a roller-bearing design.
The teeth of sprocket wheels are derived from the involute-trochoid curve. In order to engage with these teeth, the roller chain must be sufficiently accurate to avoid backlash. However, conventional roller chains can also engage with these teeth. However, this cannot eliminate backlash completely. This is why the invention provides means for reducing the friction between the teeth and the roller. This also increases the life span of the roller-and-sprocket transmission.
In terms of standards, the ANSI standard is widely used in the industry. It accounts for nearly 15% of the market in Europe and holds an advantage over the ISO standards. In North America, manufacturers of sprockets follow the ANSI code B 29.1. The ANSI code provides clear design guidelines and allows for interchangeability among different types.
There are many considerations to make when selecting a sprocket. A key factor is the transmission input. For example, if the transmission has a high horsepower, the center distance between the large and small sprockets is smaller. To compensate for this, a chain with a smaller pitch may be appropriate. Also, if the transmission has a high horsepower ratio, a multiple-strand drive is a viable option.
If you’re looking for a quality roller chain sprocket, you should check out MDS. They stock a wide range of types and sizes for a variety of industrial machinery.
Gap-tooth sprocket
A gap-tooth chain sprocket has tooth-head heights greater than the ISO tooth form height. This ensures that the pins and rollers meet at a point near the tooth head, and eliminates pulsating movement and intermittent changes in speed.
The front and rear surfaces of the sprocket are convex arcs, with radii equal to each other and the center of the tooth gap bottom. This allows for a uniform pitch and reduced friction. The tooth-face height of a gap-tooth chain sprocket is equal to the pitch of the chain, while the radii of its tooth-faces are larger than that of an ISO tooth-form.
One form of gap-tooth chain sprocket has four teeth at regular intervals. The teeth are interconnected by arc-shaped tooth gap bottoms. The resulting chain pitch is called the chain pitch. The gap-tooth sprocket can be used on various types of wheels.
ISO 606 1994 (E) defines the standard chain length, while Japanese Industrial Standards (JIS B 1801) define the standard tooth form. The ISO and Japanese Industrial Standards define two different tooth forms, namely S-tooth and U-tooth. The ISO and Japanese Industrial Standard tooth forms have different tooth pitches, but the root diameter of both forms is the same. The distance between each tooth is measured from the pitch polygon.
The tooth gap bottom circle of the gap-tooth sprocket gradually contacts the surface of the front tooth in the opposite side of the tooth gap. As this process continues, the tooth surface of the gap-tooth sprocket moves closer to the tooth head. This reduces the impact, which results in less noise.
The gap-tooth chain sprocket is an ideal solution for many applications. It allows the chain to disengage easily. With the same frequency, the teeth of the sprocket also help in regulating vibration. A sprocket with short teeth will be easier to disengage when necessary.
Another popular style of gap-tooth chain sprocket is the random polygon 64. The random polygon is a quadrilateral. Each vertex of the quadrilateral is assigned to one of the four consecutive pins on the uniform chain. The four consecutive pins are aligned in a gap-tooth pattern.
Steel split sprocket
Split sprockets are perfect for large portions of the drive system, as they can be installed without disassembling the entire shaft assembly. These sprockets are also useful in applications where there is limited workspace. They can be installed without disassembling the entire shaft assembly, minimizing the risk of damage to the conveyor system and reducing downtime.
There are several different types of split sprockets, including mat chains and table chains. Each type differs in bore diameter, number of teeth, block body style, and abrasion resistance. Some are made from steel, while others are made from a non-split material.
Split sprockets are available from many manufacturers. Typically, the split sprockets are made with two pieces of steel, which are then joined together again. This assembly technique is a cost-effective way to mount sprockets on a shaft. These sprockets can be stocked in multiple sizes and keyways.
Stainless Steel sprockets are available in stock and custom configurations. They are designed to last for years to come. These sprockets are suitable for conveyors, power transmission systems, and robotics. In addition, these sprockets offer heightened quality and durability. Some of these sprockets feature a bevel or spiral bevel gear, while others are made from helical gear.
Split sprockets are available in a variety of sizes. For instance, the RCS-03 is a plain bore type, while the RCS-04 is a finished bore type. Split sprockets are available with a split taper bushed design. They are also available with either single or multiple strands.
Double-duty sprocket
If you are looking for a heavy-duty chain sprocket, you have many choices. They come in different sizes, shapes, and materials. Some have wide teeth while others have narrow teeth. You should choose a sprocket that has the correct tooth pitch for your chain’s pitch diameter. You should also pay attention to the sprocket’s bore, or the hole in its center through which the drive shaft passes.
The type of transmission will also determine the type of sprocket you need. High-power transmissions, for example, require higher-pitch sprockets than lower-pitch models. To make sure that you choose the right sprocket for your application, check the horsepower and pitch of your transmission. If you have a low-pitch transmission, choose a smaller chain pitch. High-horsepower transmissions may also require multiple-strand drive.
There are different standards for sprockets, but ANSI standards are widely accepted. For instance, ANSI code B 29.1 requires sprockets to have two teeth per chain pitch, whereas ISO standards call for three. The double-duty sprocket, on the other hand, engages every other tooth. This helps the sprocket’s lifespan.
There are many different sprockets, and each has different performance characteristics. Generally, sprockets are made of metal or reinforced plastic and are similar to bicycle gears in their wheel-shaped design. Different types of chain sprockets have different teeth and work with different types of chains. The design of the chain and sprocket also determines the type of sprocket needed.
One popular type of double-duty sprocket is the steel-split sprocket. Its pitch is half the pitch of the chain and is usually referred to as a ‘double-duty’ sprocket. It is often used for heavy-duty purposes, as it distributes the load evenly on the chain.
While sprockets come in different tooth pitches and diameters, the recommended number of teeth is 17. The more teeth on the sprocket, the longer it will last. The height of the teeth is also important. A sprocket with more teeth will increase the life of the chain.
editor by CX 2023-07-13
China best Manufacture Agricultural Machinery Spur Gear Transmission Parts Sprocket Wheel Chains and Sprockets Industrial Pulleys best sprocket combination
Product Description
ZHangZhoug CZPT Machinery Co., Ltd
(DIN/ANSI/JIS Standard or made to drawing)
Product Description:
Detailed Photos:
Company Profile:
ZHangZhoug CZPT Machinery Co., Ltd. Is the vice chairman of chain Transmission Branch of China Machinery General parts Industry Association and a member of China chain Transmission Standardization Technical Committee.
Founded in 1954, mainly engaged in sprocket, gear, timing belt pulley, coupling production and sales, It is a large sprocket manufacturing enterprise in China, and it is also 1 of the largest standard sprocket manufacturers in the world at present. The product structure of the company has been developed from the single pattern of standard sprocket to non-standard transmission parts. Products are mainly sold in North America, South America, Europe, Africa and Japan, South Korea, the Middle East, Russia and Southeast Asia and other countries and regions, sales network all over the world.
The company has passed ISO 9002 quality assurance system certification for the first time in 1999, ISO9001: 2000 quality management system certification in 2003, ISO/TS16949 quality management system certification for the first time in 2009, ISO14001: 2004 environmental management system certification for the first time in 2571, ISO14001: 2015 environmental management system certification for 2017, and ISO9001: 2015 and IATF16949: 2016 quality management system certification for 2018. It lays a CZPT foundation for perfecting the internal management of the enterprise and opening up the external market.
The company adheres to the business philosophy of “Quality is life, technology is physique, delivery is moral, quantity is credit, service is kindred, cost is lifetime”, implementing “innovation-driven, twinning integration” upgrading strategy, promoting chain transmission products to excellence, and making every effort to create “harmonious cenfit, good quality cenfit, hundred years of cenfit”
| Standard Or Nonstandard: | Standard |
|---|---|
| Application: | Motor, Machinery, Agricultural Machinery, Car |
| Hardness: | Hardened Tooth Surface |
| Manufacturing Method: | Rolling Gear |
| Toothed Portion Shape: | Spur Gear |
| Material: | C45 |
| Customization: |
Available
| Customized Request |
|---|
How to choose the right sprocket
Knowing the size of the chain is important when looking for the right sprocket. Also, you must know the number of teeth you need and their angle. The angle between the teeth is equal to 360 degrees divided by the number of teeth. This information will help you find the right sprocket for your specific application.
Long Through Hole
Sprockets are critical to the efficiency and uptime of roller chain drives. To ensure your sprocket is installed correctly, it is important to know the dimensions of the sprocket, including its outside diameter, through-hole length, and hub diameter. Pore size is also an important consideration. Most sprockets have a 1/8″ bore, while others may have a larger bore.
Sprockets are usually secured to the shaft using ANSI standard-sized keyways and set screws. However, not all sprockets are compatible with all shaft diameters, so it is important to check the keyway size before purchasing.
Sprockets are available in a variety of styles and configurations. Some types of sprockets are welded to a solid hub, while others are bolted or split to the hub. Both types have different adjustments and you can easily change them without disassembling the device. Sprockets can be purchased from many US manufacturers in A, B or C hub configurations. For example, the hub diameter of an A-type sprocket determines its width, while a B-type sprocket has a hole for a bushing.
Sprockets are used in chain-driven motion systems, usually to carry heavy loads. It is very important to choose the right app for the right app to avoid damaging your device. If you’re not sure, learn about your system and how it’s assembled.
face width
The face width of the sprocket is limited by the meshing clearance with the chain. It does not affect tooth length. The outside diameter of the chain tip may vary depending on the type of tool used. Dimensional tolerances for keyways and set screws are also important.
diameter
One of the most important characteristics of a sprocket is its diameter. The diameter of the sprocket is used as a guide for choosing the proper sprocket size for your bike. Its number of teeth and diameter also affect the size of the chain.
The diameter of a sprocket is a function of its pitch or the distance between the centers of the link hinges. Diameters are in millimeters and expressed in standard ANSI chain numbers. Popular spacing is 3/8″ or 1/2″.
In order to make the chain drive smoothly, the sprocket and the chain should be properly matched. Incorrect pitch sprockets can damage the chain and shorten its life. Sprockets should provide precise tooth count, consistent pitch, and high wear resistance. It should also be designed to be rigid and impact resistant. CZPT chain suppliers can custom design sprockets in a variety of sizes, pitches, and diameters to suit your needs.
The number of teeth on the roller sprocket is also important. This is because the sprocket is in contact with the chain, causing frictional wear. The teeth on the sprocket can affect the durability of the chain, which is why choosing a sprocket with hardened teeth can change the world.
hub type
The hub type of the sprocket is key to proper engagement with the chain. Several options are available. The sprocket hub type is cylindrical and is available in a variety of sizes and styles. Sprockets are usually made of steel or stainless steel.
There are four main types of hubs for sprockets. They come under different names from different manufacturers, but they all share some common characteristics. These include Types A, B, and C. Each type has its own advantages and disadvantages. A-Plate sprockets are flat and have no hubs, while B-Hub sprockets are flat with hubs mounted on one side of the plate. C-shaped sprockets extend on both sides of the plate for larger pitch circle diameters and heavier axles.
A sprocket with a large pitch diameter needs a sprocket with a large pitch, and a chain with a small pitch diameter needs a chain with a small pitch. A-type sprockets are smaller and fit more closely to the equipment, while C-type sprockets need to be wider and thicker to carry more weight. Also, the pitch diameter is important because it determines whether the sprocket will fit correctly with the chain.
Steel split sprockets are easy to install and remove. They are held together by bolts on the hub, ranging in pitch size from 40 to 240. They are typically used in applications involving multiple drive shafts.
HZPT ZTB series
ZTB sprockets are an important part of a bicycle chain system. Its uptime is very important to maximize uptime and efficiency. key cSelect sprockets are characterized by size, pitch and bore. MDS accepts sprockets of various bore diameters from 1/2″ to 2″.
A sprocket is a wheel-like structure with teeth on the end. These teeth interlock with the chain, allowing simple rotational movement of large machines and equipment. ZTB sprockets are an excellent choice for a wide range of applications, including construction and agricultural machinery.
ISO sprockets have a suffix number indicating the number of chains in the chain. For example, 16B-2 sprockets have 1″ pitch and dual spools. If you’re buying sprockets for your bike, be sure to check the sprocket pitch.
The teeth on the sprocket are responsible for frictional wear, so choosing the right teeth is critical. The right teeth can increase the life of the sprocket and chain. A good sprocket has at least 17 teeth. Sprockets with a higher number of teeth last longer without causing chain slip. Typically, the teeth are the same material as the sprockets, but you can find removable teeth for a more affordable option. The teeth on the sprocket can also be hardened. Induction hardening is the most commonly used process.
ZTB sprockets can be made from many different materials. Some materials are more expensive than others, while others are softer and stronger. If you’re not sure which one to buy, try explaining the difference between the different sprockets to the sprocket manufacturer. They should be able to give you details about their interchangeability and quality.
set screw
Set screws are screws designed to hold two or more parts together. There are many different types of set screws, each with a different purpose and design. They usually come in imperial and metric sizes with a hex socket driver on one end and a cup tip on the other. They are made of hardened steel and have a black oxide finish. Some varieties have flanges, while others don’t.
Set screws with chain studs can be used in a variety of applications. For example, they can be used in agricultural equipment, heavy equipment and other industries. They come in several different sizes and thread sizes and are available in a variety of designs. Some are specific to the mining industry, while others are more general.
The company also offers custom setscrews, as well as hex, spline, square and socket heads. They have the capability to manufacture fasteners ranging from carbon steel to nickel and silicon bronze. Their products also meet Mil-I-4528 and QS 14000 standards.
editor by CX 2023-06-05